Home  /  Electrical / Electronics  /  Electronics  /  Cam-Crank-Speed Sensors

Cam-Crank-Speed Sensors


Sort: Product NamePriceCode

Crankshaft Trigger Disk with 36-1 tooth configuration.  6.75" (171.5mm) 3mm thick. Plain No Slots.

Crankshaft Trigger Disk with 36-1 tooth configuration. 6.75" (171.5mm) 3mm thick. Plain No Slots.

sku: H-TRIG1-NS

Crankshaft Trigger Plate with 36-1 tooth configuration.

6.75" (171.5mm) in Diameter and 3mm thick Mild Steel.

Bored hole is there to balance the missing tooth.
Teeth can be ground/machined off for other configuration - Note-balancing the disk would need to be performed.

$60.00

(AUD, ex gst)

Crankshaft Trigger Disk with 36-1 tooth configuration.  6.75" (171.5mm) 3mm thick. Plain No Slots.
Crankshaft Trigger Disk with 36-1 tooth configuration.  8.25" (228.6mm) 3mm thick. Plain No Slots.

Crankshaft Trigger Disk with 36-1 tooth configuration. 8.25" (228.6mm) 3mm thick. Plain No Slots.

sku: H-TRIG2-NS

Crankshaft Trigger Plate with 36-1 tooth configuration.

8.25" (228.6mm) in Diameter and 3mm thick Mild Steel.

Bored hole is there to balance the the missing tooth.
Teeth can be ground/machined off for other configuration - Note-balancing the disk would need to be performed.

$65.00

(AUD, ex gst)

Crankshaft Trigger Disk with 36-1 tooth configuration.  8.25" (228.6mm) 3mm thick. Plain No Slots.
Gear Tooth High Speed Reluctor Sensor

Gear Tooth High Speed Reluctor Sensor

sku: H-GTSEN-REL1

Hi Speed / Hi Quality Gear Tooth Crank Angle Sensor.

APPLICATIONS:
Subaru Liberty B11 Crank Angle Sensor
Subaru Liberty B12 Crank Angle Sensor
Subaru Liberty B13 Crank Angle Sensor
Subaru Impreza Crank Angle Sensor - All - 06/07
Subaru Forester Crank Angle Sensor - All - 12/07

2 Wire Reluctor Sensor, great for use with 36-1 Trigger Wheels.

$120.00

(AUD, ex gst)

Gear Tooth High Speed Reluctor Sensor
GT101 Hall Sensor Mounting Bracket

GT101 Hall Sensor Mounting Bracket

sku: H-GTSEN-MOUNT

This Mounting Bracket suits the Honeywell GT101 hall effect sensor (H-GTSEN) and our H-GTSEN2) high speed hall effect sensor.

$50.00

(AUD, ex gst)

GT101 Hall Sensor Mounting Bracket
Hall Effect Crankshaft Sensor - High RPM Version

Hall Effect Crankshaft Sensor - High RPM Version

Ideal for 36-1 Trigger Wheels and applications with teeth that are close together.


Minimum Voltage: 4.75V
Maximum Voltage: 24V
Maximum Output Current: 20mA
Maximum Tooth Frequency: 15kHz
Minimum Temperature: -40 C
Maximum Temperature: 125 C
Maximum Air Gap: 1mm-5mm Depending on Supply Voltage
Minimum Trigger Wheel Width: 2mm
Minimum Tooth Width: 2mm
Minimum Tooth Gap Width: 2mm
Minimum Tooth Gap Depth: 2mm

This uses the same body dimensions as the Honeywell GT101 Sensor.

from $120.00

(AUD, ex gst)

Hall Effect Crankshaft Sensor - High RPM Version
High Speed Hall Effect Sensor - Threaded

High Speed Hall Effect Sensor - Threaded

sku: H-GTSEN3

This high speed threaded hall effect sensor is capable of running an engine at over 15,000 RPM using a 36-1 crankshaft toothed wheel.

Threaded Section is M12 x 1mm
The main Threaded Section below the label is 46mm long.

* Supplied with 1K Ohm Resistor

$130.00

(AUD, ex gst)

High Speed Hall Effect Sensor - Threaded
gear tooth sensor Honeywell 1GT101DC / Honeywell GT101 Hall Effect Sensor

gear tooth sensor Honeywell 1GT101DC / Honeywell GT101 Hall Effect Sensor

Lipstick hall effect sensor. Works with 5 or 12 volts. Ideal for crank fired ignition systems or for sensing tail shaft or wheel speed.

This sensor is best known as a Honeywell 1GT101DC or Honeywell GT101 Gear Tooth Sensor.

from $60.00

(AUD, ex gst)

gear tooth sensor Honeywell 1GT101DC / Honeywell GT101 Hall Effect Sensor
sensor twin hall effect pick up

sensor twin hall effect pick up

sku: H-HALLA

Suits Mitsubishi Magna with Bosch distributor. Also useful to convert a distributor to ref and sync for sequential injection and ignition.

$80.00

(AUD, ex gst)

sensor twin hall effect pick up
sensor twin hall sensor for ref and sync

sensor twin hall sensor for ref and sync

sku: H-HALLB

Twin hall effect sensor element from a VT Commodore Distributor. Can be used to convert other distributors from single pulse, to reference and sync for sequential injection and ignition.

$90.00

(AUD, ex gst)

sensor twin hall sensor for ref and sync
hall effect sensor

hall effect sensor

sku: H-HALL

Replacement hall effect sensor for Bosch distributors. Also great for using as a sync sensor in distributors.

$55.00

(AUD, ex gst)

hall effect sensor
6 Cylinder Billet Sequential Distributor Trigger Cup

6 Cylinder Billet Sequential Distributor Trigger Cup

sku: H-DIST6TRIG

This billet trigger cup is machined in one piece from 1020 steel. It is far stronger than the pressed steel factory ones that can fatigue and break from high RPM or constant gear drive chatter. Part number H-HALLB is the correct hall sensor plate to used in conjunction with the trgger cup. Compatable with GM Holden VT Distributors to convert them to 6 cylinder operation with the appropriate distributor cap and rotor. Out side Diameter is 70mm

$100.00

(AUD, ex gst)

6 Cylinder Billet Sequential Distributor Trigger Cup
8 Cylinder Billet Sequential Distributor Trigger Cup

8 Cylinder Billet Sequential Distributor Trigger Cup

sku: H-DIST8TRIG

This billet trigger cup is machined in one piece from 1020 steel. It is far stronger than the pressed steel factory ones that can fatigue and break from high RPM or constant gear drive chatter. Part number H-HALLB is the correct hall sensor plate to used in conjunction with the trgger cup. Compatable with GM Holden VT Distributors. Out side diameter is 70mm

$110.00

(AUD, ex gst)

8 Cylinder Billet Sequential Distributor Trigger Cup